Auto Temperature Controller

Automatic Temperature Controllers

 

Reltech Automatic Pool Temperature Controller

Simply the best.  Three temperature readouts, easy to install, easy to use, safe and reliable.

Reltech auto pool heating controller          $365 plus postage.

 

 

MS3D Automatic Pool Temperature Controller 

autoThe MS3D solar controller is Australia’s most popular solar controller, designed to give trouble free heating from the sun.

The controller is a set and forget user friendly differential temperature controlled to give trouble free pool heating.

The MS3D features include delayed startup, tropical and winter modes and the ability to fully override the controller.

This is perhaps the most important part of the solar heating system, as it determines when the solar system should be operating and when it should not.  In most cases of complaints of insufficient heat, we have found either the controller was not operating, or the solar system was originally supplied without one at all.  The difference a good controller can make, is enormous.   Before buying extra solar collector area, make sure the automatic solar controller is operating.
The MS3D solar automatic temperature controller is a totally automated, stand alone Solar Controller. It comes with a two year warranty and has full electrical approval.   Using two probes to monitor the pool and roof temperatures, the controller is able to control the temperature of a pool with accuracy and efficiency.

 

Unique features:

  • Digital Display – easy to read pool & roof temps, and comfort level, day and night.
  • Dual Probes – two probes for greater accuracy and control.
  • Winter Mode – runs the pump daily during the winter to prevent pump lock-up.
  • Tropical Mode – allows cooling of the pool overnight, during summer in the tropics
  • Calibration – calibration of the temperature probes is possible on site.
  • Lightning Protection – sensors have lightning protection built in
  • Smart – self – diagnostic error display if not functioning properly
  • UV stable – IP23 rated housing and sensor wires are UV stabilised
  • Easy Installation – simply screw to the wall and install and connect the two sensors

SPECIFICATIONS
Operating Voltage – 240 Volts AC +/- 10%
Current Consumption – 0.02 Amps with pump off
Power Consumption – 5 Watts with pump off
Operating Temperature Range – 0 – 45 Deg C
Operating Humidity Range – 95% R.H. non-condensing.
Pump Relay – Rated to switch a 1.5 HP 240 volt motor.
Housing – UV Stabilised plastic

This equipment is not designed to be installed out in the rain. It must be protected from the weather at all times, and must not be installed within 3 metres of the swimming pool.

See Installation & operating instructions here

Price: $295.    

Express post to anywhere in Australia: $20

Replacement Pool Sensors – Brass housing pool sensor, 1.8 metre UV stable Ascon probe wire     $77
Replacement Roof Sensors – UV stable plastic housing roof sensor, 24 metre UV stable Ascon probe wire   $95

 

 

SC1 Automatic Pool Temperature Controller

solar controller sc1The SC1 is a very basic solar controller that heats your pool/spa from any solar collector.

The controller does this by sensing the temperature on the roof and the temperature of the pool. If the roof temperature rises 7° above the pool temperature and the pool temperature is below the set point, then the controller switches on the solar pump.

If the pool temperature rises 1° above the set point, or the roof temperature falls to within 2° of the pool temperature, the controller switches off the solar pump.

Features:

• Manual mode

• Simple to use

INPUT: 230/240V10A 50Hz

MAX TOTAL LOAD: 10A

Price: $265

 

SC3D Automatic Pool Temperature Controller

solar controller sc3dThe SC3D  is a micro processor based controller for heating your pool/spa from any solar collector.

The controller senses the temperature on the roof and compares it with the temperature of the pool. If the roof temperature rises 7° above the pool temperature and the pool temperature is below the set point then the controller switches on the solar pump.

If the pool temperature rises 1° above the set point, or the roof temperature falls to within 2° of the pool water temperature, the controller will switch off the solar pump.

Features:

– Sample and Hold Temperature Display

– Simple one touch buttons

– Pool, set point and roof temperature display

– Winter mode

– Manual mode

– Heating/Cooling Mode

– Temperature sensor error indication

INPUT: 230/240V 10A 50Hz

MAX TOTAL LOAD: 10A

Price: $295
SC2D Automatic Pool Temperature Controller

solar controller sc2dtThe SC2D  is a micro processor based used to heat your pool/spa from any solar collector.

The controller does this by comparing the temperature on the roof and the temperature of the pool.

If the roof temperature rises 7° above the pool temperature and the pool temperature is below the set point then the controller will switch on the solar pumpl.

If the pool temperature rises 1° above the set point or the roof temperature falls to within 2° of the pool water the controller will switch off the solar pump.

Features:

– Feather touch buttons

– Timeclock to operate filter pump and salt chlorinator

– Pool, set point and roof temperature display

– Winter mode

– Manual Mode

– Temperature sensor error indication

INPUT: 230/240V 10A 50Hz

MAX TOTAL LOAD: 10A

Price: $495
Replacement Solar Controllers & spare parts available.   Fast delivery.